Home
Components
Quiet Fans
Gelid Gale Mining 120mm High Performance Fans

Gale Extreme Mining 120mm High Performance Fan $ 14.82 15 in stock	Add to Basket
(2 customer ratings)
Gale Mining 120mm High Performance Fan $ 14.41 32 in stock	Add to Basket
More variations available Show

Gelid Gale Mining 120mm High Performance Fans

Gelid’s Gale Mining fans are high performance that are designed to produce massive amounts of airflow and static pressure to keep your PC as cool as possible. These fan are not quiet!

Features

Extremely high airflow fan
Incredible static pressure
Double ball bearings
Wide PWM range - 500 to 6000 RPM
60 dB(A) / 6000 RPM / 195 CFM *
45 dB(A) / 3500 RPM / 110 CFM †

*Gelid Gale Extreme only
†Gelid Gale only

Gelid Solutions is excited to introduce the “The Ultimate Mining Fan” GALE and GALE EXTREME, designed to maximise cooling capabilities by combining modern technologies with exceptional hardware, the gale series looks to out compete all of its competitors . Both high performing fans contain a double ball bearing system along with an optimised impeller to improve reliability and airflow. Also, a pre-installed Fan Grill is added to avoid damaging the fan blades. Its impressive specifications are worthy for any miners that value efficiency to give it a try.

GALE: Comes with a max air flow of 110 (CFM) for cooling, fan max current 0.55 (A) with a fan connector of 4 Pin PWM, max noise level 45 (dBa) also with a power draw of max. 7 (W) , static pressure of 12 (mmH2O) and a fan speed of 500 – 3500 (RPM) .

GALE EXTREME: Comes with a max air flow of 195 (CFM) for maximum cooling, fan max current 2.8 (A) with a fan connector of 4 Pin PWM, max noise level 60 (dBa) also with a power draw of max. 33.6 (W) , static pressure of 24 (mmH2O) and a fan speed of 500 – 6000 (RPM).

Show specifications and reviews for:

Specifications	Gelid Gale Extreme	Gelid Gale
Size	120x120x38 mm	120x120x38 mm
Noise Level	60 dBA max.	45 dBA max.
Airflow	195 CFM	110 CFM
Static Pressure	24.0 mm H₂O	12.0 mm H₂O
Voltage	12 V	12 V
Rotational Speed	500 - 6000 RPM	500 - 3500 RPM
Connector	4-pin PWM	4-pin PWM
Amps	2.8 A	0.55 A
Max power	33.6 W	7 W
Warranty	24 months	24 months
EAN barcode	4897025783553	4897025783546

Specifications	Gelid Gale Extreme	Gelid Gale
Size	120x120x38 mm
Noise Level	60 dBA max.	45 dBA max.
Airflow	195 CFM	110 CFM
Static Pressure	24.0 mm H₂O	12.0 mm H₂O
Voltage	12 V
Rotational Speed	500 - 6000 RPM	500 - 3500 RPM
Connector	4-pin PWM
Amps	2.8 A	0.55 A
Max power	33.6 W	7 W
Warranty	24 months
EAN barcode	4897025783553	4897025783546

Product Resources

Gelid website

FAQ

How do I measure fan size?
The size of fan you need will generally be determined by the size of the fan fitting position in your PC case. The sizes of all the fans on our website are shown as measured along any one of the fan’s four sides, NOT the distance between the fan’s screw holes! Our most popular fan size is 120mm, followed by 80mm. This isn’t really dictated by customer preference, but more by recent designs of PC cases.

As for the thickness (depth) of the fan, generally 25mm (1 inch) is by far the most common depth, although smaller fans can have shallower depths such as 15mm or even 10mm. All our fans are 25mm thick unless otherwise stated. If you have any questions about which fan you should order, please don’t hesitate to get in touch.

If you know the distance between the fan mounting screw holes but don’t know what fan size to order, please see the following table. Note that the mounting hole measurements shown below are taken horizontally or vertically between the holes and not diagonally.

Screw hole spacings and fan sizes

Space Between Screw Holes Fan Size

32mm 40mm

40mm 50mm

50mm 60mm

60mm 70mm

72mm 80mm

83mm 92mm

105mm 120mm
I received a small cable (resistor) with my fan; what is it for?
The resistor cable (also called Ultra Low Noise or ULN cable) is designed to allow the fan to run slightly slower for even quieter operation. The benefit in lower running noise is significant. Although the airflow will be reduced slightly, this usually has minimal effect on PC temperature. We would generally recommend using the ULN resistor cable for best results in almost all circumstances.
How can I tell which way the air blows through the fan?
Hold the fan so that the round fan sticker is facing you. You are looking at the rear of the fan. When you plug the fan in, the air will be blowing towards you. If you want a fan to act as an air intake, then the fan sticker will be facing the inside of the case. Some fans also have two small arrows moulded into their plastic housing - one arrow shows the direction of airflow, and the other (at 90°) shows the direction of blade rotation.
Is it possible to use a 4-pin PWM fan or CPU cooler with a motherboard which has only 3-pin fan headers on it?
Electrically, there is no problem doing this - the fourth pin on the fan cable is used purely for PWM control and is not needed in order for the fan to run. So you can plug the 4-pin fan connector onto the 3-pin motherboard fan header, leaving the fourth pin not connected to anything. The fan will potentially run at full speed, so if you would like to reduce the speed of the fan you will need to adjust the fan speed setting in your BIOS or use fan control software such as SpeedFan in Windows.

The only other problem to consider is that occasionally, components immediately adjacent to the motherboard fan header can get in the way of the larger 4-pin fan connector, physically preventing connection. This problem also occurs if you try to use an in-line fan speed controller such as the one made by Gelid.

Another avenue to explore is the possibility of using a bay-mounted fan controller. Several models are available now which provide 4-pin fan headers, so this is an easy way to use 4-pin PWM fans in a PC system which has only 3-pin fan headers on its motherboards. When using this method, you may find it necessary to disable any fan warning settings in your motherboard BIOS, since the motherboard may incorrectly believe that its CPU fan has failed when the fan is connected to a fan controller rather than directly to the motherboard itself.