120mm Silent Series Cooling Fan Discontinued
More variations available Show

Fractal Design 120mm Silent Series Cooling Fan

This fan has been specifically developed to deliver sufficient airflow while keeping the noise down.

Fractal Design “Silent Series” is a full range of silent case fans. The fans has been specifically developed to deliver sufficient airflow and still keep a low noise level. Available in sizes from 40mm up to 140mm.

Each fan is supplied with rubber fan mounts and four fan screws.

Features

Multi-purpose cooling fan
Supplied with rubber fan mounts
15.0 dB(A) / 1000 RPM / 38.3 CFM
Great value for money

Specifications	FD 120mm
Manufacturer	Fractal Design
Model	FD-FAN-120
Air volume at full speed (12V), CFM ±10%	38.3
Noise level at full speed (12V), dB(A)	15.0
Fan speed at full speed (12V), RPM ±10%	1000
Fan depth	25mm
Approximate cable length, cm	30
Power connector	3-pin
Mounting hardware included	Rubber fan mounts and screws
Rated voltage	12 VDC
Warranty	24 months
EAN barcode	7350041080145

Specifications	FD 120mm
Manufacturer	Fractal Design
Model	FD-FAN-120
Air volume at full speed (12V), CFM ±10%	38.3
Noise level at full speed (12V), dB(A)	15.0
Fan speed at full speed (12V), RPM ±10%	1000
Fan depth	25mm
Approximate cable length, cm	30
Power connector	3-pin
Mounting hardware included	Rubber fan mounts and screws
Rated voltage	12 VDC
Warranty	24 months
EAN barcode	7350041080145

Customer Reviews

Superb, couldn't be happier.

Christian Betts, 20th April 2012

Required two 120mm fans to replace the stock Cooler Master 800rpm units in my Silencio 500 case.

Tried a couple of Arctic Cooling F12 fans - far too loud, switch back to the stock fans, much quieter but shit no air.

It was between these and the Reeven Coldwing 800rpm fan, went with these for the quicker speed despite the 5db increase.

Nicely packaged, sleeved cable which is always good to see, 30cm long as well so plenty of cable to get to the fan connector at the back of the MB if you’re running PWM daisy chain fans like me.

Rubber mounters supplied as well as metal screws. Whisper quiet at 960rpm and moving plenty of air.

10/10

Great service from Quiet PC as well, ordered AM on a Thursday, dispatched with email notification later that day, delivered in Friday’s post.

Thanks a lot.

Excellent value at the price

Anonymous, 21st March 2011

Bought two of these to go into my Antec Three hundred NAS/Home Server working alongside a single Noctua 120mm fan and a single Fractal Design 140mm fan. I’d say at a guess they’re not as quiet as the noctua but they’re cheaper and from a personal point of view I prefer the stark black and white design. Still way better than the stock Antec 120mm fan that came with the case. Recommended, especially at this price.

Product Resources

Fractal Design website

FAQ

How do I measure fan size?
The size of fan you need will generally be determined by the size of the fan fitting position in your PC case. The sizes of all the fans on our website are shown as measured along any one of the fan’s four sides, NOT the distance between the fan’s screw holes! Our most popular fan size is 120mm, followed by 80mm. This isn’t really dictated by customer preference, but more by recent designs of PC cases.

As for the thickness (depth) of the fan, generally 25mm (1 inch) is by far the most common depth, although smaller fans can have shallower depths such as 15mm or even 10mm. All our fans are 25mm thick unless otherwise stated. If you have any questions about which fan you should order, please don’t hesitate to get in touch.

If you know the distance between the fan mounting screw holes but don’t know what fan size to order, please see the following table. Note that the mounting hole measurements shown below are taken horizontally or vertically between the holes and not diagonally.

Screw hole spacings and fan sizes

Space Between Screw Holes Fan Size

32mm 40mm

40mm 50mm

50mm 60mm

60mm 70mm

72mm 80mm

83mm 92mm

105mm 120mm
I received a small cable (resistor) with my fan; what is it for?
The resistor cable (also called Ultra Low Noise or ULN cable) is designed to allow the fan to run slightly slower for even quieter operation. The benefit in lower running noise is significant. Although the airflow will be reduced slightly, this usually has minimal effect on PC temperature. We would generally recommend using the ULN resistor cable for best results in almost all circumstances.
How can I tell which way the air blows through the fan?
Hold the fan so that the round fan sticker is facing you. You are looking at the rear of the fan. When you plug the fan in, the air will be blowing towards you. If you want a fan to act as an air intake, then the fan sticker will be facing the inside of the case. Some fans also have two small arrows moulded into their plastic housing - one arrow shows the direction of airflow, and the other (at 90°) shows the direction of blade rotation.
Is it possible to use a 4-pin PWM fan or CPU cooler with a motherboard which has only 3-pin fan headers on it?
Electrically, there is no problem doing this - the fourth pin on the fan cable is used purely for PWM control and is not needed in order for the fan to run. So you can plug the 4-pin fan connector onto the 3-pin motherboard fan header, leaving the fourth pin not connected to anything. The fan will potentially run at full speed, so if you would like to reduce the speed of the fan you will need to adjust the fan speed setting in your BIOS or use fan control software such as SpeedFan in Windows.

The only other problem to consider is that occasionally, components immediately adjacent to the motherboard fan header can get in the way of the larger 4-pin fan connector, physically preventing connection. This problem also occurs if you try to use an in-line fan speed controller such as the one made by Gelid.

Another avenue to explore is the possibility of using a bay-mounted fan controller. Several models are available now which provide 4-pin fan headers, so this is an easy way to use 4-pin PWM fans in a PC system which has only 3-pin fan headers on its motherboards. When using this method, you may find it necessary to disable any fan warning settings in your motherboard BIOS, since the motherboard may incorrectly believe that its CPU fan has failed when the fan is connected to a fan controller rather than directly to the motherboard itself.